关于一个CCIE考试题目的研究(重分发) (2)

2008-02-23 04:54:35来源：互联网阅读 ()

172.16.0.0/24 is subnetted, 2 subnets
O E2 172.16.1.0 [110/100] via 10.0.5.4, 00:20:22, Serial0
O E2 172.16.3.0 [110/100] via 10.0.5.4, 00:04:26, Serial0
10.0.0.0/24 is subnetted, 5 subnets
C 10.0.2.0 is directly connected, Serial1
O 10.0.3.0 [110/74] via 10.0.2.1, 00:20:22, Serial1
O 10.0.1.0 [110/74] via 10.0.2.1, 00:20:22, Serial1
O 10.0.4.0 [110/74] via 10.0.5.4, 00:20:22, Serial0
C 10.0.5.0 is directly connected, Serial0
r3
Gateway of last resort is not set

C 3.0.0.0/8 is directly connected, Loopback0
172.16.0.0/24 is subnetted, 2 subnets
O E2 172.16.1.0 [110/100] via 10.0.4.4, 00:20:44, Ethernet1
O E2 172.16.3.0 [110/100] via 10.0.4.4, 00:04:49, Ethernet1
10.0.0.0/24 is subnetted, 5 subnets
O 10.0.2.0 [110/74] via 10.0.3.1, 00:20:44, Ethernet0
C 10.0.3.0 is directly connected, Ethernet0
O 10.0.1.0 [110/20] via 10.0.3.1, 00:20:44, Ethernet0
C 10.0.4.0 is directly connected, Ethernet1
O 10.0.5.0 [110/74] via 10.0.4.4, 00:20:45, Ethernet1
r4
Gateway of last resort is not set

C 4.0.0.0/8 is directly connected, Loopback0
172.16.0.0/24 is subnetted, 2 subnets
C 172.16.1.0 is directly connected, Serial1
D 172.16.3.0 [90/2195456] via 172.16.1.5, 00:05:12, Serial1
10.0.0.0/24 is subnetted, 5 subnets
O 10.0.2.0 [110/84] via 10.0.4.3, 00:21:08, Ethernet0
O 10.0.3.0 [110/20] via 10.0.4.3, 00:21:08, Ethernet0
O 10.0.1.0 [110/30] via 10.0.4.3, 00:21:08, Ethernet0
C 10.0.4.0 is directly connected, Ethernet0
C 10.0.5.0 is directly connected, Serial0

r5
Gateway of last resort is not set

5.0.0.0/32 is subnetted, 1 subnets
C 5.5.5.5 is directly connected, Loopback0
172.16.0.0/24 is subnetted, 2 subnets
C 172.16.1.0 is directly connected, Serial1
C 172.16.3.0 is directly connected, Ethernet0
10.0.0.0/24 is subnetted, 5 subnets
D EX 10.0.2.0 [170/3072256] via 172.16.1.4, 00:02:24, Serial1
D EX 10.0.3.0 [170/3072256] via 172.16.1.4, 00:02:24, Serial1
D EX 10.0.1.0 [170/3072256] via 172.16.1.4, 00:02:24, Serial1
D EX 10.0.4.0 [170/3072256] via 172.16.1.4, 00:02:25, Serial1
D EX 10.0.5.0 [170/3072256] via 172.16.1.4, 00:02:25, Serial1

为了避免实验自身问题,我特意关闭了R1上的E0来测试R1的S1接口是否能正常路由,测试结果表明,我关闭E0后,去往目标网络的全部走R2的接口了,而我一旦启用R1的E1接口,路由便又恢复成通过R3的接口.请见这个这个文本里的测试过程.200609151401294631.txt

下面的连接是整个环境的完整配置:

200609151402410220.txt

不知道整个过程是否有错,我也担心我是否陷入了思维定试,有不同观点请点这里相互讨论.谢谢.目的为了弄明白原理.

标签：

版权申明：本站文章部分自网络，如有侵权，请联系：west999com@outlook.com
特别注意：本站所有转载文章言论不代表本站观点，本站所提供的摄影照片，插画，设计作品，如需使用，请与原作者联系，版权归原作者所有